Vážení zákazníci, v letošním roce budeme expedovat poslední objednávky ve středu 18. 12. 2024.

Těšíme se s vámi na shledanou od pondělí 06. 01. 2025.

 

Přihlásit seRegistrovat se
Jazyk czen
Menu
KontaktOBCHODNÁPOVĚDAInfobarE-ReadingNovinky
Hledání
0
Celková cena
0 Kč
Cena s DPH / bez DPH
Hlavní stránka>BS EN 1948-4:2010+A1:2013 Stationary source emissions. Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs Sampling and analysis of dioxin-like PCBs
Sponsored link
sklademVydáno: 2014-02-28
BS EN 1948-4:2010+A1:2013 Stationary source emissions. Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs Sampling and analysis of dioxin-like PCBs

BS EN 1948-4:2010+A1:2013

Stationary source emissions. Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs Sampling and analysis of dioxin-like PCBs

Formát
Dostupnost
Cena a měna
Anglicky Zabezpečené PDF
K okamžitému stažení
9486 Kč
Čtěte normu po dobu 1 hodiny. Více informací v kategorii E-READING
Čtení normy
na 1 hodinu
948.60 Kč
Čtěte normu po dobu 24 hodin. Více informací v kategorii E-READING
Čtení normy
na 24 hodin
2845.80 Kč
Anglicky Tisk
Skladem
9486 Kč
Označení normy:BS EN 1948-4:2010+A1:2013
Počet stran:68
Vydáno:2014-02-28
ISBN:978 0 580 81791 5
Status:Standard
Popis

BS EN 1948-4:2010+A1:2013


This standard BS EN 1948-4:2010+A1:2013 Stationary source emissions. Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs is classified in these ICS categories:
  • 13.040.40 Stationary source emissions

This European Standard specifies sampling from stationary sources, extraction, clean-up, identification and quantification procedures of the dioxin-like PCBs. The procedure described lays down requirements to measure the PCB congeners given in Annex A (see Table A.1). It is applicable to the 12 non- and mono-ortho PCB designated by the WHO. It is optimised to measure PCB concentrations of about 0,01 ng WHO-TEQPCB/m3.

In addition to the 12 non- and mono-ortho-PCB the present document is also applicable to measure further PCB-congeners like the “marker PCB” 28, 52, 101, 138, 153, 180 (see Annex F).

This document specifies a framework of quality control requirements for any PCB sampling, extraction, clean-up, identification and quantification methods to be applied.

As a result of their similar chemical behaviour PCBs, as shown in the validation campaign, can be sampled from stationary sources together with the PCDDs/PCDFs. Therefore, it is possible to measure PCBs together with PCDDs/PCDFs by applying EN 1948-1, -2, -3 and -4. The complete sampling procedure is described in EN 1948-1. Each of the three sampling methods of EN 1948-1 can be combined with the methods described in this document to complete the measurement procedure. EN 1948-1 is an integral part of the complete measurement procedure and is necessary for the determination of PCBs.

The analyses of the following PCB congeners is described in this European Standard and is validated in the validation campaign:

  1. Non-ortho substituted PCBs

    1. 3,3’,4,4’-TeCB(77)

    2. 3,4,4’,5-TeCB (81)

    3. 3,3’,4,4’,5-PeCB (126)

    4. 3,3’,4,4’,5,5’-HxCB (169)

  2. Mono-ortho substituted PCBs

    1. 2,3,3’,4,4’-PeCB (105)

    2. 2,3,4,4’,5-PeCB (114)

    3. 2,3’,4,4’,5-PeCB (118)

    4. 2’,3,4,4’,5-PeCB (123)

    5. 2,3,3’,4,4’,5-HxCB (156)

    6. 2,3,3’,4,4’,5’-HxCB (157)

    7. 2,3’,4,4’,5,5’-HxCB (167)

    8. 2,3,3’,4,4’,5,5’-HpCB (189)

  3. Marker PCBs

    1. 2,4,4'- TriCB (28)

    2. 2,2',5,5'-TeCB (52)

    3. 2,2',4,5,5'- PeCB (101)

    4. 2,2',3,4,4',5'- HxCB (138)

    5. 2,2',4,4',5,5'- HxCB (153)

    6. 2,2',3,4,4',5,5'- HpCB (180)


Tisk